Facebook Pixel

Auto-Line Drill Guide

SKU
AUTO-LINE-DRILL-GUIDE-GROUP

More videos are available in the Video tab below.

There are those among us who can pick up a drill, place it on a workpiece and drill a straight hole. Then, there are the remaining 99.9% of us. A drill press solves the problem…as long as the piece you want to drill fits. But if you’re not one of the 0.1% and you want a straight hole in the middle of a large piece of plywood, or in an installed cabinet, or in anything you can’t get to your drill press (or you don’t have a drill press), you want to keep reading. Introducing Woodpeckers Auto-Line Drill Guide. This new tool keeps your drill bit perfectly perpendicular while you drill, but it goes further. We added a versatile base and fence system that makes it simple to keep your hole locations right on target.  Not recommended to be used with an impact driver.

Grouped product items
Product Image Product Name Price
AUTO-LINE DRILL GUIDE DELUXE KIT - INCLUDES AUTO LINE DRILL GUIDE, 6 EXTENSION RODS, 2 FLIP STOPS AND WRENCH. AUTO-LINE DRILL GUIDE DELUXE KIT - INCLUDES AUTO LINE DRILL GUIDE, 6 EXTENSION RODS, 2 FLIP STOPS AND WRENCH. SKU: ALDG-21-DEL
(not for use with impact driver)
Sold Out! Reserve Yours Today! Expected to Ship December 14, 2024.

Add to Wish List Add to Compare
$399.99
AUTO-LINE DRILL GUIDE AUTO-LINE DRILL GUIDE SKU: ALDG-21

woodcraft coming soon

(not for use with impact driver)

Add to Wish List Add to Compare
$299.99
AUTO-LINE DRILL GUIDE FLIP STOP KIT - INCLUDES 2 FLIP STOPS, 2 EXTENSION RODS AND WRENCH. AUTO-LINE DRILL GUIDE FLIP STOP KIT - INCLUDES 2 FLIP STOPS, 2 EXTENSION RODS AND WRENCH. SKU: ALDG-21-FSK

Add to Wish List Add to Compare
$69.99
AUTO-LINE DRILL GUIDE 12"-24" FENCE GUIDE EXTENSION RODS AUTO-LINE DRILL GUIDE 12"-24" FENCE GUIDE EXTENSION RODS SKU: ALDG-EXT-21

Add to Wish List Add to Compare
$44.99
AUTO-LINE DRILL GUIDE FLIP STOP AUTO-LINE DRILL GUIDE FLIP STOP SKU: ALDG-21-FS

Add to Wish List Add to Compare
$23.99

Auto-Line Drill Guide ™

The Auto-Line starts with a high quality 1/2" chuck supported by a pair of sealed ball bearings. The shaft end is a standard quick-release fitting that will fit any cordless or corded drill. The chuck carrier holds a pair of Teflon sleeves which ride on two steel columns, keeping the chuck perfectly vertical while you drill.  One column has a spring to help you control your cut and the other has an adjustable stop collar. Notice the stop collar column has a taper milled into it. The stop needs only fingertip pressure to hold position…it’s nearly impossible to knock the stop out of position when the lock is tightened onto the taper. 

The base of the Auto-Line has laser engraved centerlines on the perimeter of the opening. Just align the bright white index marks with the witness marks on your stock for precise hole location. There’s a vee-groove milled into the base to safely drill round stock. The opening in the base has clearance for drills up to 3/4". When you need to drill holes larger than 3/4", simply remove the column caps, turn the chuck carrier around so it is outside the base and drill up to 2" holes. 

When you need holes centered on a board, mount the centering pins in the base and rotate until one pin is tight against each side of the stock. Now your bit is perfectly centered. It works on stock up to 3-1/8" wide. The centering pins store conveniently right on the top of the base when they’re not in use. We machined the Allen wrench to install the pins onto the bottom of the column caps…you’ll never have to sort through that coffee can full of Allen wrenches to find the right one.  

The versatile fence adjusts to the base along a pair of steel guide rods. As shown in the photos above, the fence can slide under the base for working close to an edge, or turn it around to get the maximum distance. When you’re working on a narrow edge, position the fence so the broad face provides extra support. And, when you’re not using the fence at all, turn it so the thin edge provides an “outrigger” to improve stability. The base is drilled and tapped for the fence guide rods on all four edges…right, left, front or back…there’s always a direction you can extend the fence. A set of optional fence guide rod extensions adds either 12" or 24" to the basic fence capacity of 7".

Like all Woodpeckers products, the Auto-Line Drill Guide is precisely machined and carefully inspected in our Strongsville, Ohio factory (just south of Cleveland). 

Credit Card Policy. Please note; if you're paying by credit card, you will not be charged until your order is ready to ship. However, Paypal and other payment services may charge you at the time the order is placed.

More Information
Country of Manufacture United States

How long are the guide rods?
A: 6.5 inches

Will longer rods be made available?
A:  Yes we do offer the rods separately for this tool?

What is the diameter of the guide rods?
A: 5/16" in diameter?

What is the length of downward travel?
A: 4.5 inches

How tall is the tool?
A: The tool stands 9-7/8 inches from the base to the top of the hex spindle for the drill chuck.

Are the guide rods from the modular bar gauge compatible with the Auto Line drill guide?
No.  They are not compatible.

What brand is the drill chuck?
A: The chuck is made in Japan by Yukiwa-Seiko.

What is the capacity of the Drill Chuck?
A:  5/64"-1/2"  shaft size

What is the longest Drill Bit  I can use with the tool?
A: 6.7" .  A common 1/2" Brad Point bit is 6.1"

How big is the base plate?
A: The base plate measures 3.75" square.